• QLG2-SE GPS Receiver module kit

GNSS/GPS Receiver module kit, including patch antenna.

This is a kit for a GNSS receiver that covers not just the United States GPS satellite network, but also Galileo (Europe), GLONASS (Russia) and Beidou (Chinese) satellite systems. GPS and Beidou are enabled by default (others require configuration via serial port). It includes a sensitive active antenna with approx 2m coax cable and SMA connectors. The kit has a 3.3V voltage regulator onboard and level converter to 5V logic levels. It may be connected directly to QRP Labs kits such as the Ultimate3S QRSS/WSPR transmitter without any pullup resistors or other components. Three LEDs provide visual indication of status. 

NOTE: kit is in manufacture for estimated end-June 2021 shipment.

The kit comprises mostly SMD components which are pre-soldered to the PCB during manufacture. Only the SMA connector, and optional connectors (USB, pin headers) are through hole and these are easy to solder. solder. 

NOTE: this is a cut-down version of the QLG2 kit and it does not have a microcontroller; therefore it does not provide a USB interface, USB to Serial converter, or optional LCD Interface. 

The GPS receiver has the following features and advantages relative to a ready-built GPS module:

1) Fun and educational kit.
2) Includes very sensitive active antenna with 2m coax, that may be easily placed separate to the PCB in a location for optimum performance.
2) Guaranteed to work with all QRP Labs kits
4) Has onboard power / data / 1pps LEDs for an immediate visual indication of what is going on.
5) Proper level conversion for use with 5V systems, not just pull-up resistors
6) Larger connection pads with 0.1-inch pitch, suitable for easy wire soldering or pin headers
7) all components already on-board, no need for anything other than wire, for connection to QRP Labs kits (and others)
8) Low cost

Click for more information, assembly manual, etc

Write a review

Note: HTML is not translated!
    Bad           Good
Captcha

QLG2-SE GPS Receiver module kit

  • Product Code: QLG2SE
  • Availability: 376
  • $20.00


Related Products

Ultimate3S QRSS/WSPR kit

Ultimate3S QRSS/WSPR kit

The Ultimate3S QRSS/WSPR Transmitter Kit transmits various QRSS, Hell, Opera, PI4 and WSPR slow-signal modes on any LF, MF, HF or VHF band (all amateur bands from 2200m to 2m or 222MHz). Thi..

$33.20

Clock kit

Clock kit

Full details are on the Clock kit page. Customisable shack clock with optional GPS interface, displays time, date, GPS parameters and temperature (two temperature sensors may optionally be con..

$19.20

Arduino shield kit

Arduino shield kit

A versatile Arduino shield kit, which could be used as: QRSS/WSPR Transmitter Signal generator (using Si5351A module or AD9850 DDS module) Clock generator (3 independent outputs, using Si535..

$14.00

Deluxe 6-band U3S set

Deluxe 6-band U3S set

This is a deluxe set of kits containing all the kits you need to build a smartly boxed, GPS-disciplined, 6-band QRSS/WSPR modes transmitter using the Ultimate3S. Deluxe set contents: The Ultimat..

$131.20

VFO/Signal Generator kit

VFO/Signal Generator kit

Full description on the QRP Labs VFO kit page. The Si5351A VFO/Signal Generator kit provides two independent output freqeuncies, 3.3V peak-peak squarewave and in the range 3.5kHz to 200MHz (Si5351A..

$33.20

ProgRock kit

ProgRock kit

This kit is a simple minimalist controller for the Si5351A Synth kit (included with the ProgRock kit). It is intended as a programmable crystal replacement. It has three independent outputs with frequ..

$18.00

HF Sinewave VFO/SigGen set

HF Sinewave VFO/SigGen set

This is a set of all the ktis you need to build the sinewave output signal generator described in App Note AN006. Using VFO kit firmware s1.03 or above, the firmware can operate the VFO/SigGen kit wit..

$76.80